In physics and thermodynamics, an equation of state is a thermodynamic equation relating state variables which describe the state of matter under a given set of physical conditions, such as pressure, volume, temperature (PVT), or internal energy.^{[1]} Equations of state are useful in describing the properties of fluids, mixtures of fluids, solids, and the interior of stars.
Thermodynamics  

The classical Carnot heat engine  


Book:Thermodynamics  
The most prominent use of an equation of state is to correlate densities of gases and liquids to temperatures and pressures. One of the simplest equations of state for this purpose is the ideal gas law, which is roughly accurate for weakly polar gases at low pressures and moderate temperatures. However, this equation becomes increasingly inaccurate at higher pressures and lower temperatures, and fails to predict condensation from a gas to a liquid. Therefore, a number of more accurate equations of state have been developed for gases and liquids. At present, there is no single equation of state that accurately predicts the properties of all substances under all conditions.
Another common use is in modeling the interior of stars, including neutron stars, dense matter (quark–gluon plasmas) and radiation fields. A related concept is the perfect fluid equation of state used in cosmology.
Equations of state can also describe solids, including the transition of solids from one crystalline state to another.
In a practical context, equations of state are instrumental for PVT calculations in process engineering problems, such as petroleum gas/liquid equilibrium calculations. A successful PVT model based on a fitted equation of state can be helpful to determine the state of the flow regime, the parameters for handling the reservoir fluids, and pipe sizing.
Measurements of equationofstate parameters, especially at high pressures, can be made using lasers.^{[2]}^{[3]}^{[4]}
Boyle's Law was perhaps the first expression of an equation of state.^{[citation needed]} In 1662, the Irish physicist and chemist Robert Boyle performed a series of experiments employing a Jshaped glass tube, which was sealed on one end. Mercury was added to the tube, trapping a fixed quantity of air in the short, sealed end of the tube. Then the volume of gas was measured as additional mercury was added to the tube. The pressure of the gas could be determined by the difference between the mercury level in the short end of the tube and that in the long, open end. Through these experiments, Boyle noted that the gas volume varied inversely with the pressure. In mathematical form, this can be stated as:
The above relationship has also been attributed to Edme Mariotte and is sometimes referred to as Mariotte's law. However, Mariotte's work was not published until 1676.
In 1787 the French physicist Jacques Charles found that oxygen, nitrogen, hydrogen, carbon dioxide, and air expand to roughly the same extent over the same 80kelvin interval. Later, in 1802, Joseph Louis GayLussac published results of similar experiments, indicating a linear relationship between volume and temperature:
Dalton's Law of partial pressure states that the pressure of a mixture of gases is equal to the sum of the pressures of all of the constituent gases alone.
Mathematically, this can be represented for n species as:
In 1834 Émile Clapeyron combined Boyle's Law and Charles' law into the first statement of the ideal gas law. Initially, the law was formulated as pV_{m} = R(T_{C} + 267) (with temperature expressed in degrees Celsius), where R is the gas constant. However, later work revealed that the number should actually be closer to 273.2, and then the Celsius scale was defined with 0 °C = 273.15 K, giving:
In 1873, J. D. van der Waals introduced the first equation of state derived by the assumption of a finite volume occupied by the constituent molecules.^{[5]} His new formula revolutionized the study of equations of state, and was most famously continued via the Redlich–Kwong equation of state and the Soave modification of RedlichKwong.
For a given amount of substance contained in a system, the temperature, volume, and pressure are not independent quantities; they are connected by a relationship of the general form
An equation used to model this relationship is called an equation of state. In the following sections major equations of state are described, and the variables used here are defined as follows. Any consistent set of units may be used, although SI units are preferred. Absolute temperature refers to use of the Kelvin (K) or Rankine (°R) temperature scales, with zero being absolute zero.
The classical ideal gas law may be written
In the form shown above, the equation of state is thus
.
If the calorically perfect gas approximation is used, then the ideal gas law may also be expressed as follows
where is the density, is the adiabatic index (ratio of specific heats), is the internal energy per unit mass (the "specific internal energy"), is the specific heat at constant volume, and is the specific heat at constant pressure.
Cubic equations of state are called such because they can be rewritten as a cubic function of V_{m}.
The Van der Waals equation of state may be written:
where is molar volume. The substancespecific constants and can be calculated from the critical properties and (noting that is the molar volume at the critical point) as:
Also written as
Proposed in 1873, the van der Waals equation of state was one of the first to perform markedly better than the ideal gas law. In this landmark equation is called the attraction parameter and the repulsion parameter or the effective molecular volume. While the equation is definitely superior to the ideal gas law and does predict the formation of a liquid phase, the agreement with experimental data is limited for conditions where the liquid forms. While the van der Waals equation is commonly referenced in textbooks and papers for historical reasons, it is now obsolete. Other modern equations of only slightly greater complexity are much more accurate.
The van der Waals equation may be considered as the ideal gas law, "improved" due to two independent reasons:
With the reduced state variables, i.e. V_{r}=V_{m}/V_{c}, P_{r}=P/P_{c} and T_{r}=T/T_{c}, the reduced form of the Van der Waals equation can be formulated:
The benefit of this form is that for given T_{r} and P_{r}, the reduced volume of the liquid and gas can be calculated directly using Cardano's method for the reduced cubic form:
For P_{r}<1 and T_{r}<1, the system is in a state of vapor–liquid equilibrium. The reduced cubic equation of state yields in that case 3 solutions. The largest and the lowest solution are the gas and liquid reduced volume.
Introduced in 1949, the RedlichKwong equation of state was a considerable improvement over other equations of the time. It is still of interest primarily due to its relatively simple form. While superior to the van der Waals equation of state, it performs poorly with respect to the liquid phase and thus cannot be used for accurately calculating vapor–liquid equilibria. However, it can be used in conjunction with separate liquidphase correlations for this purpose.
The RedlichKwong equation is adequate for calculation of gas phase properties when the ratio of the pressure to the critical pressure (reduced pressure) is less than about onehalf of the ratio of the temperature to the critical temperature (reduced temperature):
Where ω is the acentric factor for the species.
This formulation for is due to Graboski and Daubert. The original formulation from Soave is:
for hydrogen:
We can also write it in the polynomial form, with:
then we have:
where is the universal gas constant and Z=PV/(RT) is the compressibility factor.
In 1972 G. Soave^{[6]} replaced the 1/√T term of the RedlichKwong equation with a function α(T,ω) involving the temperature and the acentric factor (the resulting equation is also known as the SoaveRedlichKwong equation of state; SRK EOS). The α function was devised to fit the vapor pressure data of hydrocarbons and the equation does fairly well for these materials.
Note especially that this replacement changes the definition of a slightly, as the is now to the second power.
The SRK EOS may be written as
where
where and other parts of the SRK EOS is defined in the SRK EOS section.
A downside of the SRK EOS, and other cubic EOS, is that the liquid molar volume is significantly less accurate than the gas molar volume. Peneloux et alios (1982)^{[7]} proposed a simple correction for this by introducing a volume translation
where is an additional fluid component parameter that translate the molar volume slightly. On the liquid branch of the EOS, a small change in molar volume corresponds to a large change in pressure. On the gas branch of the EOS, a small change in molar volume corresponds to a much smaller change in pressure than for the liquid branch. Thus, the perturbation of the molar gas volume is small. Unfortunately, there are two versions that occur in science and industry.
In the first version only is translated,^{[8]} ^{[9]} and the EOS becomes
In the second version both and are translated, or the translation of is followed by a renaming of the composite parameter bc.^{[10]} This gives
The cparameter of a fluid mixture is calculated by
The cparameter of the individual fluid components in a petroleum gas and oil can be estimated by the correlation
where the Rackett compressibility factor can be estimated by
A nice feature with the volume translation method of Peneloux et alios (1982) is that it does not affect the vaporliquid equilibrium calculations.^{[11]} It should be noted that this method of volume translation can also be applied to other cubic EOSs if the cparameter correlation is adjusted to match the selected EOS.
In polynomial form:
where is the acentric factor of the species, is the universal gas constant and Z=PV/nRT is compressibility factor.
The Peng–Robinson equation of state (PR EOS) was developed in 1976 at The University of Alberta by DingYu Peng and Donald Robinson in order to satisfy the following goals:^{[12]}
For the most part the Peng–Robinson equation exhibits performance similar to the Soave equation, although it is generally superior in predicting the liquid densities of many materials, especially nonpolar ones.^{[13]} The departure functions of the Peng–Robinson equation are given on a separate article.
A modification to the attraction term in the Peng–Robinson equation of state published by Stryjek and Vera in 1986 (PRSV) significantly improved the model's accuracy by introducing an adjustable pure component parameter and by modifying the polynomial fit of the acentric factor.^{[14]}
The modification is:
where is an adjustable pure component parameter. Stryjek and Vera published pure component parameters for many compounds of industrial interest in their original journal article. At reduced temperatures above 0.7, they recommend to set and simply use . For alcohols and water the value of may be used up to the critical temperature and set to zero at higher temperatures.^{[14]}
A subsequent modification published in 1986 (PRSV2) further improved the model's accuracy by introducing two additional pure component parameters to the previous attraction term modification.^{[15]}
The modification is:
where , , and are adjustable pure component parameters.
PRSV2 is particularly advantageous for VLE calculations. While PRSV1 does offer an advantage over the Peng–Robinson model for describing thermodynamic behavior, it is still not accurate enough, in general, for phase equilibrium calculations.^{[14]} The highly nonlinear behavior of phaseequilibrium calculation methods tends to amplify what would otherwise be acceptably small errors. It is therefore recommended that PRSV2 be used for equilibrium calculations when applying these models to a design. However, once the equilibrium state has been determined, the phase specific thermodynamic values at equilibrium may be determined by one of several simpler models with a reasonable degree of accuracy.^{[15]}
One thing to note is that in the PRSV equation, the parameter fit is done in a particular temperature range which is usually below the critical temperature. Above the critical temperature, the PRSV alpha function tends to diverge and become arbitrarily large instead of tending towards 0. Because of this, alternate equations for alpha should be employed above the critical point. This is especially important for systems containing hydrogen which is often found at temperatures far above its critical point. Several alternate formulations have been proposed. Some well known ones are by Twu et all or by Mathias and Copeman.
The Elliott, Suresh, and Donohue (ESD) equation of state was proposed in 1990.^{[16]} The equation seeks to correct a shortcoming in the Peng–Robinson EOS in that there was an inaccuracy in the van der Waals repulsive term. The EOS accounts for the effect of the shape of a nonpolar molecule and can be extended to polymers with the addition of an extra term (not shown). The EOS itself was developed through modeling computer simulations and should capture the essential physics of the size, shape, and hydrogen bonding.
where:
and
where
The characteristic size parameter is related to the shape parameter through
where
Noting the relationships between Boltzmann's constant and the Universal gas constant, and observing that the number of molecules can be expressed in terms of Avogadro's number and the molar mass, the reduced number density can be expressed in terms of the molar volume as
The shape parameter appearing in the Attraction term and the term are given by
where is the depth of the squarewell potential and is given by
The model can be extended to associating components and mixtures of nonassociating components. Details are in the paper by J.R. Elliott, Jr. et al. (1990).^{[16]}
The CubicPlusAssociation (CPA) equation of state combines the SoaveRedlichKwong equation with an association term from Wertheim theory.^{[17]} The development of the equation began in 1995 as a research project that was funded by Shell, and in 1996 an article was published which presented the CPA equation of state.^{[18]}^{[19]}
where a is associated with the interaction between molecules and b takes into account the finite size of the molecules, similar to the Van der Waals equation.
The reduced coordinates are:
Although usually not the most convenient equation of state, the virial equation is important because it can be derived directly from statistical mechanics. This equation is also called the Kamerlingh Onnes equation. If appropriate assumptions are made about the mathematical form of intermolecular forces, theoretical expressions can be developed for each of the coefficients. A is the first virial coefficient, which has a constant value of 1 and makes the statement that when volume is large, all fluids behave like ideal gases. The second virial coefficient B corresponds to interactions between pairs of molecules, C to triplets, and so on. Accuracy can be increased indefinitely by considering higher order terms. The coefficients B, C, D, etc. are functions of temperature only.
One of the most accurate equations of state is that from BenedictWebbRubinStarling^{[20]} shown next. It was very close to a virial equation of state. If the exponential term in it is expanded to two Taylor terms, a virial equation can be derived:
Note that in this virial equation, the fourth and fifth virial terms are zero. The second virial coefficient is monotonically decreasing as temperature is lowered. The third virial coefficient is monotonically increasing as temperature is lowered.
where
Values of the various parameters for 15 substances can be found in K.E. Starling (1973). Fluid Properties for Light Petroleum Systems. Gulf Publishing ompany.
Statistical associating fluid theory (SAFT) equations of state use statistical mechanical methods (in particular perturbation theory) to describe the interactions between molecules in a system.^{[21]} The idea of a SAFT equation of state was first proposed by Chapman et al. in 1989,^{[21]} but since then many different SAFT equations of state have been proposed.^{[22]} Often SAFT equations represent molecules as collections of spherical particles that interact with one another.^{[21]} One popular SAFT equation represents molecules as chains composed of spherical segments (PCSAFT).^{[23]} In general, SAFT equations give more accurate results than traditional cubic equations of state, especially for systems containing liquids or solids.^{[24]}^{[25]}
Multiparameter equations of state (MEOS) can be used to represent pure fluids with high accuracy, in both the liquid and gaseous states. MEOS's represent the Helmholtz function of the fluid as the sum of ideal gas and residual terms. Both terms are explicit in reduced temperature and reduced density  thus:
Where:
The reduced density and temperature are typically, though not always, the critical values for the pure fluid. Other thermodynamic functions can be derived from the MEOS by using appropriate derivatives of the Helmholtz function; hence, because integration of the MEOS is not required, there are few restrictions as to the functional form of the ideal or residual terms. Typical MEOS use upwards of 50 fluid specific parameters, but are able to represent the fluid's properties with high accuracy. MEOS are available currently for about 50 of the most common industrial fluids including refrigerants. Mixture models also exist.
When considering water under very high pressures, in situations such as underwater nuclear explosions, sonic shock lithotripsy, and sonoluminescence, the stiffened equation of state is often used:
where is the internal energy per unit mass, is an empirically determined constant typically taken to be about 6.1, and is another constant, representing the molecular attraction between water molecules. The magnitude of the correction is about 2 gigapascals (20,000 atmospheres).
The equation is stated in this form because the speed of sound in water is given by .
Thus water behaves as though it is an ideal gas that is already under about 20,000 atmospheres (2 GPa) pressure, and explains why water is commonly assumed to be incompressible: when the external pressure changes from 1 atmosphere to 2 atmospheres (100 kPa to 200 kPa), the water behaves as an ideal gas would when changing from 20,001 to 20,002 atmospheres (2000.1 MPa to 2000.2 MPa).
This equation mispredicts the specific heat capacity of water but few simple alternatives are available for severely nonisentropic processes such as strong shocks.
An ultrarelativistic fluid has equation of state
where is the pressure, is the mass density, and is the speed of sound.
The equation of state for an ideal Bose gas is
where α is an exponent specific to the system (e.g. in the absence of a potential field, α=3/2), z is exp(μ/kT) where μ is the chemical potential, Li is the polylogarithm, ζ is the Riemann zeta function, and T_{c} is the critical temperature at which a Bose–Einstein condensate begins to form.
The equation of state from Jones–Wilkins–Lee is used to describe the detonation products of explosives.
The ratio is defined by using = density of the explosive (solid part) and = density of the detonation products. The parameters , , , and are given by several references.^{[26]} In addition, the initial density (solid part) , speed of detonation , Chapman–Jouguet pressure and the chemical energy of the explosive are given in such references. These parameters are obtained by fitting the JWLEOS to experimental results. Typical parameters for some explosives are listed in the table below.
Material  (g/cm^{3})  (m/s)  (GPa)  (GPa)  (GPa)  (GPa)  

TNT  1.630  6930  21.0  373.8  3.747  4.15  0.90  0.35  6.00 
Composition B  1.717  7980  29.5  524.2  7.678  4.20  1.10  0.35  8.50 
PBX 9501^{[27]}  1.844  36.3  852.4  18.02  4.55  1.3  0.38  10.2 
Common abbreviations:
This article includes a list of references, but its sources remain unclear because it has insufficient inline citations. (May 2009) (Learn how and when to remove this template message) 