Jumptonavigation Jumptosearch Ananemometeriscommonlyusedtomeasurewindspeed.Windspeed,orwindflowvelocity,isafundamentalatmosphericquantity.Windspeed..">
Wind speed is caused by air moving from high pressure to low pressure, usually due to changes in temperature. Note that wind direction is usually almost parallel to isobars (and not perpendicular as one might expect), due to the rotation of the earth.
Wind speed is affected by a number of factors and situations, operating on varying scales (from micro to macro scales). These include the pressure gradient, Rossby waves and jet streams, and local weather conditions. There are also links to be found between wind speed and wind direction, notably with the pressure gradient and terrain conditions.
Pressure gradient is a term to describe the difference in air pressure between two points in the atmosphere or on the surface of the Earth. It is vital to wind speed, because the greater the difference in pressure, the faster the wind flows (from the high to low pressure) to balance out the variation. The pressure gradient, when combined with the Coriolis effect and friction, also influences wind direction.
Rossby waves are strong winds in the upper troposphere. These operate on a global scale and move from West to East (hence being known as Westerlies). The Rossby waves are themselves a different wind speed from what we experience in the lower troposphere.
Local weather conditions play a key role in influencing wind speed, as the formation of hurricanes, monsoons and cyclones as freak weather conditions can drastically affect the flow velocity of the wind.
The fastest wind speed not related to tornadoes ever recorded was during the passage of Tropical Cyclone Olivia on 10 April 1996: an automatic weather station on Barrow Island, Australia, registered a maximum wind gust of 408 km/h (220 kn; 253 mph; 113 m/s). The wind gust was evaluated by the WMO Evaluation Panel who found that the anemometer was mechanically sound and the gust was within statistical probability and ratified the measurement in 2010. The anemometer was mounted 10 m above ground level (and thus 64 m above sea level). During the cyclone, several extreme gusts of greater than 300 km/h (160 kn; 83 m/s) were recorded, with a maximum 5-minute mean speed of 176 km/h (95 kn; 110 mph; 49 m/s), the extreme gust factor was in the order of 2.27–2.75 times the mean wind speed. The pattern and scales of the gusts suggest that a mesovortex was embedded in the already strong eyewall of the cyclone.
The now second highest surface wind speed ever officially recorded is 372 km/h (231 mph; 103 m/s) at the Mount Washington (New Hampshire) Observatory: 6,288 ft (1917 m) above sea level in the US on 12 April 1934, using a heated anemometer. The anemometer, specifically designed for use on Mount Washington was later tested by the US National Weather Bureau and confirmed to be accurate.
Wind speeds within certain atmospheric phenomena (such as tornadoes) may greatly exceed these values but have never been accurately measured. Directly measuring these tornadic winds is rarely done as the violent wind would destroy the instruments. A method of estimating speed is to use Doppler on Wheels to sense the wind speeds remotely, and, using this method, the figure of 486 km/h (302 mph; 135 m/s) during the 1999 Bridge Creek–Moore tornado in Oklahoma on 3 May 1999 is often quoted as the highest-recorded surface wind speed, although another figure of 512 kilometres per hour (318 mph) has also been quoted for the same tornado. Yet another number used by the Center for Severe Weather Research for that measurement is 486 ± 32 km/h (302 ± 20 mph). However, speeds measured by Doppler radar are not considered official records.
An anemometer is one of the tools used to measure wind speed. A device consisting of a vertical pillar and three or four concave cups, the anemometer captures the horizontal movement of air particles (wind speed).
Another tool used to measure wind velocity includes a GPS combined with pilot tube. A fluid flow velocity tool, the Pitot tube is primarily used to determine the air velocity of an aircraft.
Wind speed is a common factor in the design of structures and buildings around the world. It is often the governing factor in the required lateral strength of a structure's design.
In the United States, the wind speed used in design is often referred to as a "3-second gust" which is the highest sustained gust over a 3-second period having a probability of being exceeded per year of 1 in 50 (ASCE 7-05). This design wind speed is accepted by most building codes in the United States and often governs the lateral design of buildings and structures.
In Canada, reference wind pressures are used in design and are based on the "mean hourly" wind speed having a probability of being exceeded per year of 1 in 50. The reference wind pressure (q) is calculated in Pascals using the following equation: q=(1/2)pV² where p is the air density in kg/m³ and V is wind speed in m/s.
Historically, wind speeds have been reported with a variety of averaging times (such as fastest mile, 3-second gust, 1-minute and mean hourly) which designers may have to take into account. To convert wind speeds from one averaging time to another, the Durst Curve was developed which defines the relation between probable maximum wind speed averaged over t seconds, Vt, and mean wind speed over one hour V3600.